shrinkage deformation câu

Always allow for 3% shrinkage upon the first wash or dry clean.Luôn luôn cho phép co ngót 3% khi giặt khô lần đầu tiên. Strong hygrosc...

Too long breaks in watering lead to leaf deformation.Quá lâu nghỉ trong tưới nước dẫn đến biến dạng lá. deformation of the ear structu...

2.The leaves became smaller and its edge will become dry shrinkage.2) Các lá trở nên nhỏ hơn và cạnh của nó sẽ trở nên khô co lại. 2.T...

Together, these qualities allow pathways to form that allow the movement of water into, and through, along with the cracking that occur...

Because employees will know that inventory is being carefully tracked, internal shrinkage will dwindle.Bởi vì nhân viên sẽ biết rằng hà...

A security camera system will help to cut down on inventory shrinkage and the negative financial impact they will have on your business...

An important difference between Nylon 6 & 66 is mold shrinkage.Một sự khác biệt quan trọng giữa Nylon 6 & 66 là độ co khuôn.

Molding shrinkage of small products for dimensional stability.Đúc các co rút của các sản phẩm nhỏ cho chiều ổn định. 1.PEEK plastic ma...

For molding workers, adjusting the processing conditions is a way to solve the problem of plastic shrinkage.Đối với nhân viên đúc, điều...

DB: perhaps the rate of shrinkage would be greatly slowed down.David Bohm: Có lẽ tỷ lệ của co rút sẽ được chậm lại rất nhiều. Since 20...

Haida shrinking machines have been high technology and optimum residual shrinkage in the market for decades,spreads over 100 customers ...

They also build into their contracts a shrinkage allowance over the inventory they process.Họ cũng xây dựng vào hợp đồng của họ một kho...

Click to apply a shrinkage factor to the plastic part, the part solid is selected automatically, select Origin for Scale about, Resin t...

It has the smallest shrinkage ratio in inorganic materials and is caulked with special polymer adhesive to prevent cracking.Nó có tỷ lệ...

of the earth’s geothermal gradient (rate ofĐộ co ngót thể tích của đất (degree of volume shrinkage of soil) In order to solve the volum...

Average Volumetric Shrinkage: 13.0% (Green to 6% M.C.)Độ co rút thể tích trung bình: 11.9% (Green to 6% M.C.) Is the volumetric shrink...

Special additives such as mica can be added to the PET to minimize bending deformation.Các chất phụ gia đặc biệt như mica có thể được t...

Nine, ACM acrylate rubber seal: Excellent resistance to oil, high temperature and weather resistance, but mechanical strength, compress...

If we think of the parameter of H as time then H describes a continuous deformation of f into g, at time 0 we have the function f.Nếu t...

Therefore, as long as the deformation energy is within the range of forming energy, cold forging can easily obtain good dimensional acc...

Such a high temperature is necessary to avoid strain hardening of metal during the deformation process.Kiểu này nhiệt độ cực cao là cần...

As the deformation rate of the polyethylene increases, LDPE demonstrates a dramatic rise in viscosity because of chain entanglement.Khi...

Forging is mainly classified according to the forming method and the deformation temperature.Rèn được phân loại chủ yếu theo phương phá...

Although the process that forms drumlins is not fully understood, their shape implies that they are products of the plastic deformation...

Under the same load conditions, the elastic deformation of Si3N4 ceramic is small.Trong cùng điều kiện tải, sự biến dạng đàn hồi của Si...